VoiceOps
By thread
voiceops@voiceops.org
By month
Messages by month
- ----- 2026 -----
- November
- October
- September
- August
- July
- June
- May
- April
- March
- February
- January
- ----- 2025 -----
- December
- November
- October
- September
- August
- July
- June
- May
- April
- March
- February
- January
- ----- 2024 -----
- December
- November
- October
- September
- August
- July
- June
- May
- April
- March
- February
- January
- ----- 2023 -----
- December
- November
- October
- September
- August
- July
- June
- May
- April
- March
- February
- January
- ----- 2022 -----
- December
- November
- October
- September
- August
- July
- June
- May
- April
- March
- February
- January
- ----- 2021 -----
- December
- November
- October
- September
- August
- July
- June
- May
- April
- March
- February
- January
- ----- 2020 -----
- December
- November
- October
- September
- August
- July
- June
- May
- April
- March
- February
- January
- ----- 2019 -----
- December
- November
- October
- September
- August
- July
- June
- May
- April
- March
- February
- January
- ----- 2018 -----
- December
- November
- October
- September
- August
- July
- June
- May
- April
- March
- February
- January
- ----- 2017 -----
- December
- November
- October
- September
- August
- July
- June
- May
- April
- March
- February
- January
- ----- 2016 -----
- December
- November
- October
- September
- August
- July
- June
- May
- April
- March
- February
- January
- ----- 2015 -----
- December
- November
- October
- September
- August
- July
- June
- May
- April
- March
- February
- January
- ----- 2014 -----
- December
- November
- October
- September
- August
- July
- June
- May
- April
- March
- February
- January
- ----- 2013 -----
- December
- November
- October
- September
- August
- July
- June
- May
- April
- March
- February
- January
- ----- 2012 -----
- December
- November
- October
- September
- August
- July
- June
- May
- April
- March
- February
- January
- ----- 2011 -----
- December
- November
- October
- September
- August
- July
- June
- May
- April
- March
- February
- January
- ----- 2010 -----
- December
- November
- October
- September
- August
- July
- June
- May
- April
- March
- February
- January
- ----- 2009 -----
- December
- November
- October
- September
- August
- July
October 2009
- 62 participants
- 195 messages
ShoreTel PBX interop with Broadsoft Based Switch.
by ujjval@simplesignal.com
>From what I remember, the first time I looked it was unchecked, as our reseller provisioned the SIp trunks into it remotely. However, the system was used in their lab before, I cannot tell if it was checked or not then? Chances are it was checked before the PBX got to me.
Ujjval Karihaloo
VP Voice Engineering
IP Phone: +13032428610
E-Fax: +17202391690
SimpleSignal Inc.
88 Inverness Circle East
Suite K105
Englewood, CO 80112
[cid:image001.jpg at 01CA50F0.4AD13C40]<http://www.simplesignal.com/>
From: Jason L. Nesheim [mailto:jnesheim at cytek.biz]
Sent: Monday, October 19, 2009 7:10 PM
To: Ujjval Karihaloo
Cc: voiceops at voiceops.org
Subject: Re: [VoiceOps] ShoreTel PBX interop with Broadsoft Based Switch.
Was the box checked before you provisioned the SIP trunks in the system? Did you disable it before provisioning SIP in the system?
--
Jason Nesheim
----- Original Message -----
From: "Ujjval Karihaloo" <ujjval at simplesignal.com>
To: "Jason L. Nesheim" <jnesheim at cytek.biz>
Cc: voiceops at voiceops.org
Sent: Monday, October 19, 2009 6:05:05 PM
Subject: RE: [VoiceOps] ShoreTel PBX interop with Broadsoft Based Switch.
Correct, the sequence for rebooting was just an attempt to get the Phone not to use port 5004?mine was already unchecked..na deven after rebooting the phone continues to use RTP port 5004?
While testing with ShoreTel Phones would be ideal, I continued my testing with Sip Softphones, as I could get those to work until I ran into transfer issues.
Ujjval Karihaloo
VP Voice Engineering
IP Phone: +13032428610
E-Fax: +17202391690
SimpleSignal Inc.
88 Inverness Circle East
Suite K105
Englewood, CO 80112
[cid:image001.jpg at 01CA50F0.4AD13C40]<http://www.simplesignal.com/>
From: Jason L. Nesheim [mailto:jnesheim at cytek.biz]
Sent: Monday, October 19, 2009 7:03 PM
To: Ujjval Karihaloo
Cc: voiceops at voiceops.org
Subject: Re: [VoiceOps] ShoreTel PBX interop with Broadsoft Based Switch.
Uncheck the "Always Use Port 5004" box under Call Control -> Options in ShoreWare Director. You may need to reboot the phones and Shoregear switch after changing this. Technically this should already be a disabled (and unchangeable) option in the system whenever SIP trunks or extensions exist.
Our reseller provided ways to override the Shoretel setting (rebooting all devices, Shoregear switch, Shoreware Director, and Shoretel IP 530 phone in that sequence) so it does not use Port 5004 to send RTP out to, but it does not seem to work.
I've never heard of anything like this, unless it was in reference to what should be done after the use port 5004 option is disabled.
--
Jason Nesheim
----- Original Message -----
From: "Ujjval Karihaloo" <ujjval at simplesignal.com>
To: "Ujjval Karihaloo" <ujjval at simplesignal.com>, voiceops at voiceops.org
Sent: Monday, October 19, 2009 5:40:55 PM
Subject: Re: [VoiceOps] ShoreTel PBX interop with Broadsoft Based Switch.
Anyone has any ideas about this one?
Ujjval Karihaloo
VP Voice Engineering
IP Phone: +13032428610
E-Fax: +17202391690
SimpleSignal Inc.
88 Inverness Circle East
Suite K105
Englewood, CO 80112
[cid:image001.jpg at 01CA50F0.4AD13C40]<http://www.simplesignal.com/>
From: voiceops-bounces at voiceops.org [mailto:voiceops-bounces at voiceops.org] On Behalf Of Ujjval Karihaloo
Sent: Monday, October 05, 2009 11:49 AM
To: voiceops at voiceops.org
Subject: [VoiceOps] ShoreTel PBX interop with Broadsoft Based Switch.
Hi All, We are trying to interop the ShoreTel (behind a Edgemarc ? which registers on behalf of the Shoretel as from what I know Shoretel cannot send a SIP register) with our Broadsoft setup..I was wondering if someone has done it.
We are trying to get the Shoretel up and running, while I have it configured as per the Broadsoft Partner config guide, the Shoretel system still continues to use Port 5004 for RTP (which is its default behavior when not configured for SIP), this is resulting in one way audio. Our reseller provided ways to override the Shoretel setting (rebooting all devices, Shoregear switch, Shoreware Director, and Shoretel IP 530 phone in that sequence) so it does not use Port 5004 to send RTP out to, but it does not seem to work.
Call flow is as follows:
Looks like the IP530 phone sends the calls through Shoregear switch to the Broadsoft infrastructure,
As the call is answered, the 200 OK comes back from the Broadsoft side; the Edgemarc NATs the 200OK & sends its private IP in the SDP and a Port, however, I see the IP 530 phone stream RTP to the Private IP of the Edgemarc but to port 5004 all the time.
Our reseller provided ways to override the Shoretel setting (rebooting all devices, Shoregear switch, Shoreware Director, and Shoretel IP 530 phone in that sequence) so it does not use Port 5004 to send RTP out to, but it does not seem to work.
Thx
Ujjval Karihaloo
_______________________________________________
VoiceOps mailing list
VoiceOps at voiceops.org
https://puck.nether.net/mailman/listinfo/voiceops
Oct. 20, 2009
ShoreTel PBX interop with Broadsoft Based Switch.
by jnesheim@cytek.biz
Was the box checked before you provisioned the SIP trunks in the system? Did you disable it before provisioning SIP in the system?
--
Jason Nesheim
----- Original Message -----
From: "Ujjval Karihaloo" <ujjval at simplesignal.com>
To: "Jason L. Nesheim" <jnesheim at cytek.biz>
Cc: voiceops at voiceops.org
Sent: Monday, October 19, 2009 6:05:05 PM
Subject: RE: [VoiceOps] ShoreTel PBX interop with Broadsoft Based Switch.
Correct, the sequence for rebooting was just an attempt to get the Phone not to use port 5004?mine was already unchecked..na deven after rebooting the phone continues to use RTP port 5004?
While testing with ShoreTel Phones would be ideal, I continued my testing with Sip Softphones, as I could get those to work until I ran into transfer issues.
Ujjval Karihaloo
VP Voice Engineering
IP Phone: +13032428610
E-Fax: +17202391690
SimpleSignal Inc.
88 Inverness Circle East
Suite K105
Englewood, CO 80112
bvoip
From: Jason L. Nesheim [mailto:jnesheim at cytek.biz]
Sent: Monday, October 19, 2009 7:03 PM
To: Ujjval Karihaloo
Cc: voiceops at voiceops.org
Subject: Re: [VoiceOps] ShoreTel PBX interop with Broadsoft Based Switch.
Uncheck the "Always Use Port 5004" box under Call Control -> Options in ShoreWare Director. You may need to reboot the phones and Shoregear switch after changing this. Technically this should already be a disabled (and unchangeable) option in the system whenever SIP trunks or extensions exist.
Our reseller provided ways to override the Shoretel setting (rebooting all devices, Shoregear switch, Shoreware Director, and Shoretel IP 530 phone in that sequence) so it does not use Port 5004 to send RTP out to, but it does not seem to work.
I've never heard of anything like this, unless it was in reference to what should be done after the use port 5004 option is disabled.
--
Jason Nesheim
----- Original Message -----
From: "Ujjval Karihaloo" <ujjval at simplesignal.com>
To: "Ujjval Karihaloo" <ujjval at simplesignal.com>, voiceops at voiceops.org
Sent: Monday, October 19, 2009 5:40:55 PM
Subject: Re: [VoiceOps] ShoreTel PBX interop with Broadsoft Based Switch.
Anyone has any ideas about this one?
Ujjval Karihaloo
VP Voice Engineering
IP Phone: +13032428610
E-Fax: +17202391690
SimpleSignal Inc.
88 Inverness Circle East
Suite K105
Englewood, CO 80112
bvoip
From: voiceops-bounces at voiceops.org [mailto:voiceops-bounces at voiceops.org] On Behalf Of Ujjval Karihaloo
Sent: Monday, October 05, 2009 11:49 AM
To: voiceops at voiceops.org
Subject: [VoiceOps] ShoreTel PBX interop with Broadsoft Based Switch.
Hi All, We are trying to interop the ShoreTel (behind a Edgemarc ? which registers on behalf of the Shoretel as from what I know Shoretel cannot send a SIP register) with our Broadsoft setup..I was wondering if someone has done it.
We are trying to get the Shoretel up and running, while I have it configured as per the Broadsoft Partner config guide, the Shoretel system still continues to use Port 5004 for RTP (which is its default behavior when not configured for SIP), this is resulting in one way audio. Our reseller provided ways to override the Shoretel setting (rebooting all devices, Shoregear switch, Shoreware Director, and Shoretel IP 530 phone in that sequence) so it does not use Port 5004 to send RTP out to, but it does not seem to work.
Call flow is as follows:
Looks like the IP530 phone sends the calls through Shoregear switch to the Broadsoft infrastructure,
As the call is answered, the 200 OK comes back from the Broadsoft side; the Edgemarc NATs the 200OK & sends its private IP in the SDP and a Port, however, I see the IP 530 phone stream RTP to the Private IP of the Edgemarc but to port 5004 all the time.
Our reseller provided ways to override the Shoretel setting (rebooting all devices, Shoregear switch, Shoreware Director, and Shoretel IP 530 phone in that sequence) so it does not use Port 5004 to send RTP out to, but it does not seem to work.
Thx
Ujjval Karihaloo
_______________________________________________
VoiceOps mailing list
VoiceOps at voiceops.org
https://puck.nether.net/mailman/listinfo/voiceops
Oct. 20, 2009
ShoreTel PBX interop with Broadsoft Based Switch.
by ujjval@simplesignal.com
Correct, the sequence for rebooting was just an attempt to get the Phone not to use port 5004?mine was already unchecked..na deven after rebooting the phone continues to use RTP port 5004?
While testing with ShoreTel Phones would be ideal, I continued my testing with Sip Softphones, as I could get those to work until I ran into transfer issues.
Ujjval Karihaloo
VP Voice Engineering
IP Phone: +13032428610
E-Fax: +17202391690
SimpleSignal Inc.
88 Inverness Circle East
Suite K105
Englewood, CO 80112
[cid:image001.jpg at 01CA50EF.119C4420]<http://www.simplesignal.com/>
From: Jason L. Nesheim [mailto:jnesheim at cytek.biz]
Sent: Monday, October 19, 2009 7:03 PM
To: Ujjval Karihaloo
Cc: voiceops at voiceops.org
Subject: Re: [VoiceOps] ShoreTel PBX interop with Broadsoft Based Switch.
Uncheck the "Always Use Port 5004" box under Call Control -> Options in ShoreWare Director. You may need to reboot the phones and Shoregear switch after changing this. Technically this should already be a disabled (and unchangeable) option in the system whenever SIP trunks or extensions exist.
Our reseller provided ways to override the Shoretel setting (rebooting all devices, Shoregear switch, Shoreware Director, and Shoretel IP 530 phone in that sequence) so it does not use Port 5004 to send RTP out to, but it does not seem to work.
I've never heard of anything like this, unless it was in reference to what should be done after the use port 5004 option is disabled.
--
Jason Nesheim
----- Original Message -----
From: "Ujjval Karihaloo" <ujjval at simplesignal.com>
To: "Ujjval Karihaloo" <ujjval at simplesignal.com>, voiceops at voiceops.org
Sent: Monday, October 19, 2009 5:40:55 PM
Subject: Re: [VoiceOps] ShoreTel PBX interop with Broadsoft Based Switch.
Anyone has any ideas about this one?
Ujjval Karihaloo
VP Voice Engineering
IP Phone: +13032428610
E-Fax: +17202391690
SimpleSignal Inc.
88 Inverness Circle East
Suite K105
Englewood, CO 80112
[cid:image001.jpg at 01CA50EF.119C4420]<http://www.simplesignal.com/>
From: voiceops-bounces at voiceops.org [mailto:voiceops-bounces at voiceops.org] On Behalf Of Ujjval Karihaloo
Sent: Monday, October 05, 2009 11:49 AM
To: voiceops at voiceops.org
Subject: [VoiceOps] ShoreTel PBX interop with Broadsoft Based Switch.
Hi All, We are trying to interop the ShoreTel (behind a Edgemarc ? which registers on behalf of the Shoretel as from what I know Shoretel cannot send a SIP register) with our Broadsoft setup..I was wondering if someone has done it.
We are trying to get the Shoretel up and running, while I have it configured as per the Broadsoft Partner config guide, the Shoretel system still continues to use Port 5004 for RTP (which is its default behavior when not configured for SIP), this is resulting in one way audio. Our reseller provided ways to override the Shoretel setting (rebooting all devices, Shoregear switch, Shoreware Director, and Shoretel IP 530 phone in that sequence) so it does not use Port 5004 to send RTP out to, but it does not seem to work.
Call flow is as follows:
Looks like the IP530 phone sends the calls through Shoregear switch to the Broadsoft infrastructure,
As the call is answered, the 200 OK comes back from the Broadsoft side; the Edgemarc NATs the 200OK & sends its private IP in the SDP and a Port, however, I see the IP 530 phone stream RTP to the Private IP of the Edgemarc but to port 5004 all the time.
Our reseller provided ways to override the Shoretel setting (rebooting all devices, Shoregear switch, Shoreware Director, and Shoretel IP 530 phone in that sequence) so it does not use Port 5004 to send RTP out to, but it does not seem to work.
Thx
Ujjval Karihaloo
_______________________________________________
VoiceOps mailing list
VoiceOps at voiceops.org
https://puck.nether.net/mailman/listinfo/voiceops
Oct. 20, 2009
ShoreTel PBX interop with Broadsoft Based Switch.
by jnesheim@cytek.biz
Uncheck the "Always Use Port 5004" box under Call Control -> Options in ShoreWare Director. You may need to reboot the phones and Shoregear switch after changing this. Technically this should already be a disabled (and unchangeable) option in the system whenever SIP trunks or extensions exist.
Our reseller provided ways to override the Shoretel setting (rebooting all devices, Shoregear switch, Shoreware Director, and Shoretel IP 530 phone in that sequence) so it does not use Port 5004 to send RTP out to, but it does not seem to work. I've never heard of anything like this, unless it was in reference to what should be done after the use port 5004 option is disabled .
--
Jason Nesheim
----- Original Message -----
From: "Ujjval Karihaloo" <ujjval at simplesignal.com>
To: "Ujjval Karihaloo" <ujjval at simplesignal.com>, voiceops at voiceops.org
Sent: Monday, October 19, 2009 5:40:55 PM
Subject: Re: [VoiceOps] ShoreTel PBX interop with Broadsoft Based Switch.
Anyone has any ideas about this one?
Ujjval Karihaloo
VP Voice Engineering
IP Phone: +13032428610
E-Fax: +17202391690
SimpleSignal Inc.
88 Inverness Circle East
Suite K105
Englewood, CO 80112
bvoip
From: voiceops-bounces at voiceops.org [mailto:voiceops-bounces at voiceops.org] On Behalf Of Ujjval Karihaloo
Sent: Monday, October 05, 2009 11:49 AM
To: voiceops at voiceops.org
Subject: [VoiceOps] ShoreTel PBX interop with Broadsoft Based Switch.
Hi All, We are trying to interop the ShoreTel (behind a Edgemarc ? which registers on behalf of the Shoretel as from what I know Shoretel cannot send a SIP register) with our Broadsoft setup..I was wondering if someone has done it.
We are trying to get the Shoretel up and running, while I have it configured as per the Broadsoft Partner config guide, the Shoretel system still continues to use Port 5004 for RTP (which is its default behavior when not configured for SIP), this is resulting in one way audio. Our reseller provided ways to override the Shoretel setting (rebooting all devices, Shoregear switch, Shoreware Director, and Shoretel IP 530 phone in that sequence) so it does not use Port 5004 to send RTP out to, but it does not seem to work.
Call flow is as follows:
Looks like the IP530 phone sends the calls through Shoregear switch to the Broadsoft infrastructure,
As the call is answered, the 200 OK comes back from the Broadsoft side; the Edgemarc NATs the 200OK & sends its private IP in the SDP and a Port, however, I see the IP 530 phone stream RTP to the Private IP of the Edgemarc but to port 5004 all the time.
Our reseller provided ways to override the Shoretel setting (rebooting all devices, Shoregear switch, Shoreware Director, and Shoretel IP 530 phone in that sequence) so it does not use Port 5004 to send RTP out to, but it does not seem to work.
Thx
Ujjval Karihaloo
_______________________________________________
VoiceOps mailing list
VoiceOps at voiceops.org
https://puck.nether.net/mailman/listinfo/voiceops
Oct. 20, 2009
Shoretel 9.0 Call transfer using SIP softphone Xlite/Eyebeam
by jnesheim@cytek.biz
You could probably request the parameter list from ShoreTel TAC. I do not know of any documentation which provides these.
--
Jason Nesheim
----- Original Message -----
From: "Ujjval Karihaloo" <ujjval at simplesignal.com>
To: "Jason L. Nesheim" <jnesheim at cytek.biz>
Cc: VoiceOps at voiceops.org
Sent: Monday, October 19, 2009 5:36:49 PM
Subject: RE: [VoiceOps] Shoretel 9.0 Call transfer using SIP softphone Xlite/Eyebeam
I am using an Edgwater device instead of a Ingate Siparator. Where can I find all the Customer Parameters for a Sip Profile on ShoreTel?
From: Jason L. Nesheim [mailto:jnesheim at cytek.biz]
Sent: Monday, October 19, 2009 5:45 PM
To: Ujjval Karihaloo
Cc: VoiceOps at voiceops.org
Subject: Re: [VoiceOps] Shoretel 9.0 Call transfer using SIP softphone Xlite/Eyebeam
You have two options that I know of, one which may or may not work depending on your network.
You can add an Ingate Firewall/Siparator to the deployment. This device will locally handle the REFER operation and actually send the call back to the ShoreTel PBX (because of the Refer-To target) which then routes it through the appropriate trunk on the PBX stripping the access code before it sends it back to the Ingate. This also avoids the SDPless Invite on transfer issue below.
You can also try manually disabling the use of REFER as the transfer method. To disable REFER you can edit the SIP profile for your trunk and set "DontFwdREFER=1" under the custom parameters box. Be aware that this may cause other problems with call transfers and three way calling. I've been unable to get the PBX to work correctly on SIP trunks without the Ingate when REFER is disabled and G729 is used. This is due to the ShoreTel sending SDPless Invites when starting three way conferences and then subsequently failing to handle a 200 OK response with G729a in the offer list (it simply drops the messages). If you restrict the list of codecs in the SDP response to the Invite to G711u only it should work for you.
--
Jason Nesheim
----- Original Message -----
From: "Ujjval Karihaloo" <ujjval at simplesignal.com>
To: "Jason L. Nesheim" <jnesheim at cytek.biz>
Cc: VoiceOps at voiceops.org
Sent: Monday, October 19, 2009 3:46:07 PM
Subject: RE: [VoiceOps] Shoretel 9.0 Call transfer using SIP softphone Xlite/Eyebeam
Here is what I see happening?This is from ShoreGear Switch?
It seems like on the SIP Trunk I am setup to prefix all calls with a 9, but when I transfer using Eyebeam Shoretel messes up the number (converts 93035551000 to 9+13035551000) in the REFER msg to the Broadsoft platform, hence call fails?
If I press Xfer on EBeam and then dial 13035551000 (Don?t prefix it with a 9), it seems to work?
I think it?s a setting on the Shoretel?.Any ideas..?
From: Jason L. Nesheim [mailto:jnesheim at cytek.biz]
Sent: Monday, October 19, 2009 4:31 PM
To: Ujjval Karihaloo
Cc: VoiceOps at voiceops.org
Subject: Re: [VoiceOps] Shoretel 9.0 Call transfer using SIP softphone Xlite/Eyebeam
Could you provide a SIP signaling capture of the communication between the Shoretel PBX, Ingate, and Broadworks?
There are several possible issues but it would be difficult to say what applies to your scenario without a capture.
--
Jason Nesheim
----- Original Message -----
From: "Ujjval Karihaloo" <ujjval at simplesignal.com>
To: VoiceOps at voiceops.org
Sent: Monday, October 19, 2009 9:19:21 AM
Subject: [VoiceOps] Shoretel 9.0 Call transfer using SIP softphone Xlite/Eyebeam
I am testing Shoretel shoretel with Broadsoft and Call transfer seems to fail.
Eyebeam ? Shoregear ? SIP Provider(Broadsoft) ? PSTN
Eyebeam use calls a cell phone on the PSTN side and then tried to transfer the call to PSTN user#2, Has anyone tested this with a SIP Softphone registered to Shoretel ?
_______________________________________________
VoiceOps mailing list
VoiceOps at voiceops.org
https://puck.nether.net/mailman/listinfo/voiceops
Oct. 20, 2009
ShoreTel PBX interop with Broadsoft Based Switch.
by ujjval@simplesignal.com
Anyone has any ideas about this one?
Ujjval Karihaloo
VP Voice Engineering
IP Phone: +13032428610
E-Fax: +17202391690
SimpleSignal Inc.
88 Inverness Circle East
Suite K105
Englewood, CO 80112
[cid:image001.jpg at 01CA50EB.B177DE40]<http://www.simplesignal.com/>
From: voiceops-bounces at voiceops.org [mailto:voiceops-bounces at voiceops.org] On Behalf Of Ujjval Karihaloo
Sent: Monday, October 05, 2009 11:49 AM
To: voiceops at voiceops.org
Subject: [VoiceOps] ShoreTel PBX interop with Broadsoft Based Switch.
Hi All, We are trying to interop the ShoreTel (behind a Edgemarc - which registers on behalf of the Shoretel as from what I know Shoretel cannot send a SIP register) with our Broadsoft setup..I was wondering if someone has done it.
We are trying to get the Shoretel up and running, while I have it configured as per the Broadsoft Partner config guide, the Shoretel system still continues to use Port 5004 for RTP (which is its default behavior when not configured for SIP), this is resulting in one way audio. Our reseller provided ways to override the Shoretel setting (rebooting all devices, Shoregear switch, Shoreware Director, and Shoretel IP 530 phone in that sequence) so it does not use Port 5004 to send RTP out to, but it does not seem to work.
Call flow is as follows:
Looks like the IP530 phone sends the calls through Shoregear switch to the Broadsoft infrastructure,
As the call is answered, the 200 OK comes back from the Broadsoft side; the Edgemarc NATs the 200OK & sends its private IP in the SDP and a Port, however, I see the IP 530 phone stream RTP to the Private IP of the Edgemarc but to port 5004 all the time.
Our reseller provided ways to override the Shoretel setting (rebooting all devices, Shoregear switch, Shoreware Director, and Shoretel IP 530 phone in that sequence) so it does not use Port 5004 to send RTP out to, but it does not seem to work.
Thx
Ujjval Karihaloo
Oct. 20, 2009
Shoretel 9.0 Call transfer using SIP softphone Xlite/Eyebeam
by ujjval@simplesignal.com
I am using an Edgwater device instead of a Ingate Siparator. Where can I find all the Customer Parameters for a Sip Profile on ShoreTel?
From: Jason L. Nesheim [mailto:jnesheim at cytek.biz]
Sent: Monday, October 19, 2009 5:45 PM
To: Ujjval Karihaloo
Cc: VoiceOps at voiceops.org
Subject: Re: [VoiceOps] Shoretel 9.0 Call transfer using SIP softphone Xlite/Eyebeam
You have two options that I know of, one which may or may not work depending on your network.
You can add an Ingate Firewall/Siparator to the deployment. This device will locally handle the REFER operation and actually send the call back to the ShoreTel PBX (because of the Refer-To target) which then routes it through the appropriate trunk on the PBX stripping the access code before it sends it back to the Ingate. This also avoids the SDPless Invite on transfer issue below.
You can also try manually disabling the use of REFER as the transfer method. To disable REFER you can edit the SIP profile for your trunk and set "DontFwdREFER=1" under the custom parameters box. Be aware that this may cause other problems with call transfers and three way calling. I've been unable to get the PBX to work correctly on SIP trunks without the Ingate when REFER is disabled and G729 is used. This is due to the ShoreTel sending SDPless Invites when starting three way conferences and then subsequently failing to handle a 200 OK response with G729a in the offer list (it simply drops the messages). If you restrict the list of codecs in the SDP response to the Invite to G711u only it should work for you.
--
Jason Nesheim
----- Original Message -----
From: "Ujjval Karihaloo" <ujjval at simplesignal.com>
To: "Jason L. Nesheim" <jnesheim at cytek.biz>
Cc: VoiceOps at voiceops.org
Sent: Monday, October 19, 2009 3:46:07 PM
Subject: RE: [VoiceOps] Shoretel 9.0 Call transfer using SIP softphone Xlite/Eyebeam
Here is what I see happening?This is from ShoreGear Switch?
It seems like on the SIP Trunk I am setup to prefix all calls with a 9, but when I transfer using Eyebeam Shoretel messes up the number (converts 93035551000 to 9+13035551000) in the REFER msg to the Broadsoft platform, hence call fails?
If I press Xfer on EBeam and then dial 13035551000 (Don?t prefix it with a 9), it seems to work?
I think it?s a setting on the Shoretel?.Any ideas..?
From: Jason L. Nesheim [mailto:jnesheim at cytek.biz]
Sent: Monday, October 19, 2009 4:31 PM
To: Ujjval Karihaloo
Cc: VoiceOps at voiceops.org
Subject: Re: [VoiceOps] Shoretel 9.0 Call transfer using SIP softphone Xlite/Eyebeam
Could you provide a SIP signaling capture of the communication between the Shoretel PBX, Ingate, and Broadworks?
There are several possible issues but it would be difficult to say what applies to your scenario without a capture.
--
Jason Nesheim
----- Original Message -----
From: "Ujjval Karihaloo" <ujjval at simplesignal.com>
To: VoiceOps at voiceops.org
Sent: Monday, October 19, 2009 9:19:21 AM
Subject: [VoiceOps] Shoretel 9.0 Call transfer using SIP softphone Xlite/Eyebeam
I am testing Shoretel shoretel with Broadsoft and Call transfer seems to fail.
Eyebeam--> Shoregear--> SIP Provider(Broadsoft)--> PSTN
Eyebeam use calls a cell phone on the PSTN side and then tried to transfer the call to PSTN user#2, Has anyone tested this with a SIP Softphone registered to Shoretel ?
_______________________________________________
VoiceOps mailing list
VoiceOps at voiceops.org
https://puck.nether.net/mailman/listinfo/voiceops
Oct. 20, 2009
Shoretel 9.0 Call transfer using SIP softphone Xlite/Eyebeam
by jnesheim@cytek.biz
You have two options that I know of, one which may or may not work depending on your network.
You can add an Ingate Firewall/Siparator to the deployment. This device will locally handle the REFER operation and actually send the call back to the ShoreTel PBX (because of the Refer-To target) which then routes it through the appropriate trunk on the PBX stripping the access code before it sends it back to the Ingate. This also avoids the SDPless Invite on transfer issue below.
You can also try manually disabling the use of REFER as the transfer method. To disable REFER you can edit the SIP profile for your trunk and set "DontFwdREFER=1" under the custom parameters box. Be aware that this may cause other problems with call transfers and three way calling. I've been unable to get the PBX to work correctly on SIP trunks without the Ingate when REFER is disabled and G729 is used. This is due to the ShoreTel sending SDPless Invites when starting three way conferences and then subsequently failing to handle a 200 OK response with G729a in the offer list (it simply drops the messages). If you restrict the list of codecs in the SDP response to the Invite to G711u only it should work for you.
--
Jason Nesheim
----- Original Message -----
From: "Ujjval Karihaloo" <ujjval at simplesignal.com>
To: "Jason L. Nesheim" <jnesheim at cytek.biz>
Cc: VoiceOps at voiceops.org
Sent: Monday, October 19, 2009 3:46:07 PM
Subject: RE: [VoiceOps] Shoretel 9.0 Call transfer using SIP softphone Xlite/Eyebeam
Here is what I see happening?This is from ShoreGear Switch?
It seems like on the SIP Trunk I am setup to prefix all calls with a 9, but when I transfer using Eyebeam Shoretel messes up the number (converts 93035551000 to 9+13035551000) in the REFER msg to the Broadsoft platform, hence call fails?
If I press Xfer on EBeam and then dial 13035551000 (Don?t prefix it with a 9), it seems to work?
I think it?s a setting on the Shoretel?.Any ideas..?
From: Jason L. Nesheim [mailto:jnesheim at cytek.biz]
Sent: Monday, October 19, 2009 4:31 PM
To: Ujjval Karihaloo
Cc: VoiceOps at voiceops.org
Subject: Re: [VoiceOps] Shoretel 9.0 Call transfer using SIP softphone Xlite/Eyebeam
Could you provide a SIP signaling capture of the communication between the Shoretel PBX, Ingate, and Broadworks?
There are several possible issues but it would be difficult to say what applies to your scenario without a capture.
--
Jason Nesheim
----- Original Message -----
From: "Ujjval Karihaloo" <ujjval at simplesignal.com>
To: VoiceOps at voiceops.org
Sent: Monday, October 19, 2009 9:19:21 AM
Subject: [VoiceOps] Shoretel 9.0 Call transfer using SIP softphone Xlite/Eyebeam
I am testing Shoretel shoretel with Broadsoft and Call transfer seems to fail.
Eyebeam ? Shoregear ? SIP Provider(Broadsoft) ? PSTN
Eyebeam use calls a cell phone on the PSTN side and then tried to transfer the call to PSTN user#2, Has anyone tested this with a SIP Softphone registered to Shoretel ?
_______________________________________________
VoiceOps mailing list
VoiceOps at voiceops.org
https://puck.nether.net/mailman/listinfo/voiceops
Oct. 19, 2009
Shoretel 9.0 Call transfer using SIP softphone Xlite/Eyebeam
by ujjval@simplesignal.com
Here is what I see happening?This is from ShoreGear Switch?
It seems like on the SIP Trunk I am setup to prefix all calls with a 9, but when I transfer using Eyebeam Shoretel messes up the number (converts 93035551000 to 9+13035551000) in the REFER msg to the Broadsoft platform, hence call fails?
If I press Xfer on EBeam and then dial 13035551000 (Don?t prefix it with a 9), it seems to work?
I think it?s a setting on the Shoretel?.Any ideas..?
From: Jason L. Nesheim [mailto:jnesheim at cytek.biz]
Sent: Monday, October 19, 2009 4:31 PM
To: Ujjval Karihaloo
Cc: VoiceOps at voiceops.org
Subject: Re: [VoiceOps] Shoretel 9.0 Call transfer using SIP softphone Xlite/Eyebeam
Could you provide a SIP signaling capture of the communication between the Shoretel PBX, Ingate, and Broadworks?
There are several possible issues but it would be difficult to say what applies to your scenario without a capture.
--
Jason Nesheim
----- Original Message -----
From: "Ujjval Karihaloo" <ujjval at simplesignal.com>
To: VoiceOps at voiceops.org
Sent: Monday, October 19, 2009 9:19:21 AM
Subject: [VoiceOps] Shoretel 9.0 Call transfer using SIP softphone Xlite/Eyebeam
I am testing Shoretel shoretel with Broadsoft and Call transfer seems to fail.
Eyebeam--> Shoregear--> SIP Provider(Broadsoft)--> PSTN
Eyebeam use calls a cell phone on the PSTN side and then tried to transfer the call to PSTN user#2, Has anyone tested this with a SIP Softphone registered to Shoretel ?
_______________________________________________
VoiceOps mailing list
VoiceOps at voiceops.org
https://puck.nether.net/mailman/listinfo/voiceops
Oct. 19, 2009
Shoretel 9.0 Call transfer using SIP softphone Xlite/Eyebeam
by jnesheim@cytek.biz
Could you provide a SIP signaling capture of the communication between the Shoretel PBX, Ingate, and Broadworks?
There are several possible issues but it would be difficult to say what applies to your scenario without a capture.
--
Jason Nesheim
----- Original Message -----
From: "Ujjval Karihaloo" <ujjval at simplesignal.com>
To: VoiceOps at voiceops.org
Sent: Monday, October 19, 2009 9:19:21 AM
Subject: [VoiceOps] Shoretel 9.0 Call transfer using SIP softphone Xlite/Eyebeam
I am testing Shoretel shoretel with Broadsoft and Call transfer seems to fail.
Eyebeam ? Shoregear ? SIP Provider(Broadsoft) ? PSTN
Eyebeam use calls a cell phone on the PSTN side and then tried to transfer the call to PSTN user#2, Has anyone tested this with a SIP Softphone registered to Shoretel ?
_______________________________________________
VoiceOps mailing list
VoiceOps at voiceops.org
https://puck.nether.net/mailman/listinfo/voiceops
Oct. 19, 2009